Customer problem: Does V2020.03 BMW ICOM only support English and Chinese? When I run 500 GB SSD ISTA+, there are only two languages can be selected. How to change to other languages?
It is recommended to use Lenovo ThinkPad: T61, T400, T410, T420, T430, X61, X200, X201, X220 X230 and other laptop with Intel chipset, such as I3 I5 / I7 series.
It’s tested ok to reset ABS bleeding for 2015 Chevrolet Suburban using Launch ThinkDiag OBD2 diagnostic tool.
Car: 2015 Chevrolet Suburban (light duty truck)
Device:Launch THINKCAR ThinkDiag OBD2 full system code reader
http://www.obdiitool.co.uk/wholesale/thinkdiag-obd2-full-system.html Procedures: Install ThinkDiag APP on Android or IOS smart phone Plug the ThinkDiag device into OBDII port in your vehicle until the green light appears Turn on the ignition Run ThinkDiag APP Press the second icon at the bottom left of the APP screen to enter ThinkStore page
Press “…” show full purchased software
There are two ways to reset ABS bleeding:
1.Select GM car make
2.Select RESETBLEED function
Here we choose the No.2 method to operate
Connect Bluetooth automatically
Select car manufacturer: GM
Make sure turn on the ignition switch
Pay attention to the info:
If the first bit of the VIN is the L letter, please select path: CHINESECAR->SGM
Press [OK] enter GM software
Press [Cancel] exit
Just press OK to continue-
Tap Manually Select (Via Model)-> LD Trk, MPV, Incomplete-> Chevrolet Truck-> Suburban-> 2015-2018
And it will read out the car year
The ABS bleeding reset instructions will display on the screen, just follow it to operate:1.To perform the automated bleed and vehicle learn procedures. Follow the service manual and equipment manufacturer’s instructions.Connect the required brake bleed equipment Connect battery charger to 12V battery Turn ignition on Place transmission in the Park or Neutral position. Note: ignition must remain in the run position during the entire process.2.Connect bleeder ball to vehicle and set to 300 kpa. Note: Do not open any bleeder screw until instructed 3.Stop vehicle. This test cannot be run while moving Configuring brakes bleeding system! They’re sending pressure through the line to clear out all the air, you’re going to hear this about four separate times so it’s going to happen on the front right and then front left, back right and back left.
The notification is letting us know that the traction control was on and off
Once clear all four of these in that notification will be gone
Follow the prompts to reset automated bleed-left front/rear, bleed-right rear
Ford VCM II with latest version V101 comes with multi-language. It not only can read and clear diagnostic trouble codes, but also provides full dealer diagnostic capabilities for most 16 pin Fords, including all new 2020 Ford vehicles. Here have collected some frequently asked questions below. Hope it helps!
Q: Does Ford vcm2 support Ford Falcon (AU) from 2002 to 2005?
A: Yes.
Q: Can vcm2 support BCM module replace?
A: Yes.
Q: Can VCM2 software work on Win10?
A: It should be ok. Some customers installed it successfully on Win10. Win7 is better to install.
Q: I want to IDS FORD to do many functions, such as program keys, bcm modules, program flash modules off 2018-2017 year. Which tool or software can support?
A: Ford VCMII IDS V101 + original GM online subscription.
Q: Does VCM2 for Ford IDS V101 support reprogramming of the TCM on the 2008 Lincoln MCX?
A: Yes.
Q: Which software comes with VCMII IDS V101 package?
A: Only v101 software in the CD.
Q: I want to do diagnose ford fiesta，ford transit custom, euro 6 diesel 2017 and above, which tool is recommended to use?
A: VCMII FORD.
Q: What’s the difference between Ford VCMII IDS V101 and VCM II 2 in 1 Ford V116 diagnostic tool?
A: Ford VCMII IDS V101 is more stable to do ECU programming than VCM II 2 in 1 Ford V116. Other functions are same.
Q: When finish installing VCM2 for Ford IDS V101 and start to use, it pops up “trial period has expired”, how to solve?
A: Please modify the date to software version date.
Q: I bought a ford vcm ii in 2016. It worked well before. But when I change a new Windows 10 computer, and install virtual machine and software, the device failed to use. It cannot communicate with computer and the green light is not on.
A: Please check whether the all the device drivers have been installed well or not.
Part 1: Xhorse Toyota 8A All Key Lost adapter function
Xhorse Toyota 8A Non-smart key adapter for all keys lost, works well with VVDI2, VVDI Key Tool Max& Mini OBD tool without dismantling the IMMO box.
Note: the Toyota 8A adapter cannot be used alone, needs to work with VVDI2 or key tool max.
Part 2: Xhorse Toyota 8A All Key Lost adapter vehicle coverage
Xhorse Toyota 8A Non-smart key adapter supportsToyota 8A H chip (non-smart) all keys lost from year 2014 to 2019 via OBD, without disassembling Immobilizer box, incl. Levin, Corolla, Rav4, Prado, Land Cruiser, Camry, Highlander, Reiz and Sienna.
Part 3: Xhorse Toyota 8A all keys lost adapter how to use
Here is the fullpackage including platform adapter, OBD connector and harness adapter.
Platform adapter with harness adapter can be directly connected to the transfer box to add key on the platform, as well as reset the anti-theft box.
If we operate in the car, work on bench without disassembling it. It doesn’t need to remove the anti-theft box. We need to connect platform adapter with OBD connector. OBD connector with car OBD
The positive and negative red and black clips of the battery to the positive and negative
The blue short connector is clamped on the car’s ignition switch No.2 relay
OBD connector connected to the car
The long blue connector is connected to the ignition switch contact switch plug on
This specific operations and connections are opened below.
1.Preparation:
Step 1: Find the fuse box on the car and open it
Note: Different models have different fuse positions and relay box positions
Look for the No.2 ignition switch according to the position on the fuse box
And unplug the relay
Step 2: Remove the protective shell Exposing the ignition lock There is an inductive contact switch line on the ignition lock, unplug it
There is a two-pin cable on this plug. After a while, you need to insert the long blue plug on it.
The preparatory work has been completed 2.Connection: This OBD is connected to the device
This OBD connect with the car
Two power clips are clamped on the battery
Make sure take away the red positive electrode
The positive and negative poles are champed in the corresponding positions
The blue short is connected to the position of the No.2 ignition switch relay
OBD port connect with the car
This is connected to VVDI2 or Key tool Max
Connect the long blue signal wire to the contact switch wire
Insert the key without the chip into the ignition switch
Punch it
Put the super chip into VVDI2 coil
3.Run VVDI2 software Enter the VVDI2 software transponder programmer Click “OBD Make master key directly”
When communicating, the system dashboard will automatically light up Reading anti-theft… The instrument light on the car will flash Follow the prompt to put the super chip into the VVDI2 antenna and click OK
If have already put it in, just click OK to continue Writing to chip Note: It needs to calculate online, so you need to connect to the Internet when operating. Generate the master key chip successfully
Disconnect the thread and recover the vehicle removing Put the chip into the key Then insert the key into ignition switch to turn on, start normally
Part 4: Xhorse Toyota 8A all keys lost adapter FAQs Q1: What tool can be used to this connector to car key programmer? A1: VVDI2 or Key Tool Max+ Mini OBD Tool. Q2: Toyota 8A Non-smart Key Adapter can work with VVDI2. Are there any requirements for the license of Xhorse VVDI2? Can the VVDI2 basic version also be used? A2: It doesn’t need any token or authorization. The basic version is also supported. Q3: Even without vvdi2 i can use it with mini obd tool? A3: Yes. Q4: What years would this work on? A4: It works on all years. Q5: Toyota Aygo 2015 System H all keys lost. Does this computer program the chip? Hilux? Hiace? A5: Yes, it does. No problem for Toyota Hiace and Hilux (2015-2019 IMMO box) Q6: What kinds of key can be supported? Proximity or just keyed? A6: Not smart key. Just key. Q7: What versions of modules IMMO H supports? A7: IMMO box F3-F4-K6-S6 Q8: Is this used to program toyota H immo box on bench? A8: Not on bench. On car via obd, no need to dismantle the dash anymore. With vvdi2 new software + key tool max, you can read immo data and make keys directly to IMMO or other option is barracuda and tango on bench. With this set must be on car because there is a connection to fuse box and obd and ign coil. Q9: Possible to program smart key Land cruiser after 2016? A9: Yes, it will. Q10: Does this need a subscription for Toyota or is this a bypass? A10: Bypass. Q11: Does it support new 2020 Toyota keys? A11: Yes. Q12:Does a programmer of the degree need hello besides this adapter? A12: The adapter cannot be used alone. It should be work with vvdi2 or key tool max+ mini obd tool. Q13: Can it be used simultaneously with a barracuda? A13: No. Barracuda is a ecu programmer. The adapter requires a OBD programmer to program key. Get XHORSE Toyota 8A Non-smart Key Adapter for All Key Lost No Disassembly: http://www.obdiitool.co.uk/wholesale/xhorse-toyota-8a-adapter.html
HUMZOR NEXZDAS Pro with 10 inch tablet is a professional Bluetooth full system auto diagnostic tool. It works on wide vehicle over 70 car brands. Here will share the guide to download, update and using tips.
Part 2: How to update HUMZOR NEXZDAS Pro on Auto diagnostic tools? Free update on the official website: https://www.humzor.com/ or update for wide vehicle models in the App Store of the software. No other fees with lifetime free upgrade with more powerful versions. More advanced functions are under developing now for later release, such as ECU coding & programming, more supported models, etc. All free to update gradually.
Part 3: How to use HUMZOR NexzDAS PRO 10 inch tablet quickly?
1.When finish install NexzDAS APP, open it directly with network working
2.Register with an available email and set up your login password
3.Bind the device, get the serial number and activation code from the password envelope
4.Plug NexzDAS PRO device into the vehicle’s OBD port
Turn on the ignition switch with engine off (the red light turns on)
5.Run NexzDAS APP, connect Bluetooth automatically, and the blue light on the device turns on
6.Select the car model and functions you need, then start to do diagnosis.
Learn more details about Humzor NexzDAS Pro with 10inch tablet full system diagnostic tool, click here:
Learn more details about Humzor NexzDAS Pro with 10inch tablet full system diagnostic tool, click here:
Recently, one customer gave a feedback that he could open v03.2020 MB SD C4 software with MB SD C5 when using the license. But he got the errors when opened the following files as below:
1.Config Assist
2.DTS Monaco 8.13
3.EPC&WIS(admin 12345)
4.Open Your Star SD4 2020.3
5.XENTRY Diagnosis/XENTRY Diagnosis SIM
Solution offered by obdiitool.co.uk engineer:
Except the first one, others are not activated.
1.Solution for Config Assist:
Press “Win+R” button at the same time to open run window, input “Services.msc” in the Windows service, and start Configassist service
2.Solution DTS Monaco 8.13 error:
Please send the ID to your dealer to activate.
3.Solution for other errors above:
The MB SD C4 software activation video comes with the software, you can find the video on the screen of computer.
Or you can follow the video offered below to operate directly.
Problem: It always asks to update when using VVDI Mini key tool. After download and update successfully, but it will prompt to update as well.
Solution:
Try to uninstall and download to install again or install by other Android or IOS smartphone. There is no need to pay extra fee again if you login with the same account number.
Customer problem: When I install ODIS V5.1.6 software by my VAS6154 diagnostic interface. An error pops up with the words “Framework start failed with “13” in the offboard Diag Launcher process. There is not file to select in the local directory.
Solution offered by obdiitool.co.uk engineer:
You need to install a virtual optical drive, map the more 30 unzipped files into a CD.
And in the URL option, click “Select local directory” to select the corresponding drive.
Please follow the ODIS 5.1.6 software installation video to install again.
VXDIAG VCX NANO 5054 ODIS V5.1.6 Free Download and installation tips can refer to this article:
obdiitool.co.uk Tech Support Blog 